Film Cleanliness


Quality organizations in the Pharmaceutical Industry are rightly concerned with any issues that may affect product integrity. Any solids, liquids, or vapors that may be released in close proximity to a product are suspect. The presence of any of these places additional burden on Quality laboratories.

There is considerable confusion about what can happen when you don’t use the correct film for containment devices. In reality, all films are prone to the same concerns – or lack thereof! All  films start their life at the time they are first drawn from a molten pool of polymer. To prevent the film from crystallizing and becoming exceedingly fragile it is shock cooled. The film is drawn upwards out of the molten polymer. To keep it from collapsing on itself it is blown into a large bubble shape with copious quantities of air. The air used is cool ambient air. The moment cool air contacts the skin of the bubble immediately above the molten polymer pool the film is shock cooled. This prevents the film, which is now a solid solution, from annealing to form an ordered matrix. Annealing is a common occurrence when a simple strip heater is used to seal a polyethylene bag creating a crystalline edge along the heat seal which is more fragile than the bulk film. The effect is more pronounced when a thick film, e.g. 20 mil thick, is heat sealed without shock cooling. Even holding the film on either side of the heat seal will cause parting along the sides of the seal.

The film bubble is drawn up to the cutting and folding mechanism where it is collapsed upon itself. The air inside and outside the bubble is room air. The technology for most film formulations has not changed dramatically over the years. Blowing is not done in a clean room or with purified air.

The friction due to air flow causes the film to become statically charged. As a result it is capable of attracting small airborne particles from the air surrounding the bubble – both inside and outside. The supplier makes no attempt to clean the film before shipping the rolled material to a user.

The good news is that the dust does not readily release from the film surface because of residual static charge. Accrued  dust remains stable on the surface of the film under normal conditions due to  this residual charge – which is enhanced during handling. However use of copious quantities of liquid, or use for materials packaging, can result in extraction or abrasion of particles from the film surface.

Film cleanliness can be tested empirically:

In a customer study, vendors were asked to submit film for cleanliness testing. Swatches measuring

100 sq. cm were aggressively treated in purified water and the resulting suspension filtered for comparison with standard part-per-million (ppm) filters. While most films showed a low level of staining (~4 ppm) there were two exceptions:

One film showed no observable staining. This was traced to the vendor pre-cleaning the sample on the understanding that cleaned film was to be provided.

The second exception was a film that produced a stain so black that it could not be quantified. This was traced to vendor use of a third party fabricator

A second request was made for film without disclosing the purpose. The results were the same except that the stain created by the previously clean film was in line with the others.

In a follow-up study a variety of polymeric films were cleaned using alcohol swabs resulting in stain free filters.

Most vendors of flexible containment perform tempering, cutting, assembly, inspection, and packaging under clean conditions. To use actual clean room conditions for these operations is meaningless when the stock film is not certifiably clean in the first place.

If a particle free film is desired, no degree of assurance is achieved when clean room fabrication is used. The accrued dust from film blowing, storage, and shipping will still be present on the film surface.

However, a clean product can be delivered by requesting post production cleaning of the inside surfaces of the fabricated product. At FabOhio Inc. this is performed by qualified operators in a clean environment using isopropyl alcohol swabs.

The learning point is that sub-contracted fabricators need to be audited as carefully as the primary vendor. FabOhio Inc. does not use sub-contractors, however we do fabricate products for other vendors under the same stringent quality requirements as our own products. Every product that leaves our loading dock in Uhrichsville, OH is manufactured, inspected, overpacked, and documented to the same standards that have been approved by independent industry auditors. FabOhio Inc. stands firmly behind all products leaving our only fabrication site whether provided for our customers or for other vendors.

FabOhio Inc. is pleased to deliver products which have been swab cleaned when requested.

The same products can also be radiation conditioned once sealed in an overpack. Details about our most commonly used film are available at our web site: 

Film Composition:

Linear Low Density PolyEthylene (LLDPE) film was established as the standard reference against which all other film formulations are compared. LLDPE bulk used for blown film is a homogeneous polymer consisting of reacted monomer and the catalyst fully integrated into the final melt. LLDPE film shows poor long term resistance to some low molecular weight solvents in both the liquid and vapor states, e.g. methylene chloride and methyl alcohol. These are also solvents to which most polymeric films show poor resistance.

The European Medicines Agency (EMA) has established criteria for conductance of polymeric materials involved in intimate product contact which places serious constraints on formulation by allowing only a limited number of approved additives. They also list a battery of solvents against which a polymer film intended for product contact must be tested.

Any additive to LLDPE, or any film polymer formulation, raises concern about the integrity of the film material. While such polymer films may show stability to liquid solvents, this is not a predictor of solvent vapor stability.

Modifier additives to the formulation do not incorporate into the film matrix by reaction, but rather in a state of solid solution within the polymer. The additives physical characteristics remain virtually unchanged. Additives on the approved list are all volatile. The vapor pressure of the additive is a consideration. For example plasticizers added to PolyVinyl Chloride (PVC) can be identified by the characteristic smell emanating from PVC film. For this reason PVC is not used to contain product or intermediate when other alternatives are available.

Polymer films not involved in intimate product contact, e.g. glove bags, flexible enclosures, and  flexible room barriers are not subject to the same criteria as product contact films. There is no justification for using a specialty film for such applications.

A polymeric film is only approved for product contact once short and long term stability tests with product contact have been completed. Short term accelerated stability testing occurs at elevated temperatures and requires 90 or more days. Long term stability testing takes 2 years at a minimum, with the actual product storage requirements determining the maximum duration. Stability tests are conducted by the user or a sub-contract laboratory. Vendors of flexible containment products rarely become involved in such testing. Refer to our earlier blog for details on a user experience.

The user is ultimately responsible for selection of a flexible film for use in their application. FabOhio Inc. does not claim superior qualities for the multiple film choices that we use to make glove bags, flexible enclosures, flexible room enclosures, glove sleeves, and other products that leave our site.

FabOhio Inc. will be pleased to advise you on the optimum film and conditioning requirements for your containment project. We give due consideration to the physical and chemical environments in which they are to be used, based on our extensive data base of comparable applications. We consider both application requirements and cost efficiency for your benefit. We make available a number of film formulations. Our products are made by qualified personnel under clean conditions. Fabricated products are available pre-swabbed for cleanliness. Radiation conditioned products are conditioned in their sealed overpacks with the radiation tags still attached when shipped to the customer.

In summary:

Any raw material used as an additive for blown film complicates the product contact matrix

Vendor claims of an approved film formulation do not implicitly guarantee that the film is an  acceptable or superior product for use in your application

A blown film is only approved for your use in extended product contact applications after you have completed and documented both short term accelerated and long term stability studies

Containment barrier products fabricated from blown film in a clean room are intrinsically no improvement over products fabricated using clean manufacturing practices

With current technology for blowing film, the only assurance of a film surface having lower          than currently measurable surface contamination is to require the final product to be cleaned with alcohol swabs immediately before sealing in a similarly cleaned overpack

Product materials used for stability studies should be actual production materials, not stored reserve materials

Flexible film applications not involving product storage do not benefit from the use of custom film formulations

When auditing a provider of flexible film containment products, all manufacturing sources            should be audited to include sub-contract providers

Contact FabOhio Inc. at or (740) 922 4233 for pricing and availability, and all special services. You will find our costs to be among the most competitive in the business. Over 98% of our supplies are sourced within the USA. All of our products have documented traceability to the source.


This entry was posted in Uncategorized. Bookmark the permalink.

24 Responses to Film Cleanliness

  1. Pingback: Trackback

  2. Do you mind if I quote a couple of your posts as long as I
    provide credit and sources back to your blog? My blog site
    is in the very same niche as yours and my visitors would definitely benefit from some of
    the information you present here. Please let me know if this ok with you.
    Thank you!

  3. Greate post. Keep writing such kind of information on your blog.
    Im really impressed by your site.
    Hello there, You’ve done an excellent job. I’ll definitely digg it and in my view suggest to my friends.

    I am confident they will be benefited from this web site.

  4. Pretty nice post. I simply stumbled upon your blog and wanted to say that I’ve
    really enjoyed browsing your blog posts.
    After all I will be subscribing for your rss feed and I hope you write once more very soon!

  5. What’s up to all, it’s actually a good for me to pay a visit this web page, it consists of useful Information.

  6. If you want to grow your know-how only keep visiting this web site and be updated with the newest information posted here.

  7. I know this if off topic but I’m looking into starting my own weblog
    and was curious what all is needed to get setup?

    I’m assuming having a blog like yours would cost a pretty penny?
    I’m not very web savvy so I’m not 100% sure. Any recommendations or advice would
    be greatly appreciated. Cheers

  8. What’s up colleagues, how is everything, and what you
    wish for to say on the topic of this post, in my view its really remarkable for

  9. Rodger says:

    you’re in reality a good webmaster. The website loading pace is amazing.
    It sort of feels that you’re doing any distinctive trick.
    In addition, The contents are masterwork. you have done a wonderful job on this topic!

  10. Gricelda says:

    Hi, i think that i saw you visited my site thus i
    came to “return the favor”.I’m attempting to find things to improve my site!I
    suppose its ok to use some of your ideas!!

  11. Conchita says:

    Hi there colleagues, how is everything, and what
    you wish for to say about this paragraph,
    in my view its truly remarkable in support of me.

  12. Julietta says:

    You are so cool! I don’t suppose I’ve read through
    anything like that before. So good to discover another person with genuine thoughts on this subject.
    Seriously.. thanks for starting this up. This website
    is one thing that’s needed on the internet, someone with a bit of

  13. DanaPDonlyuk says:

    This text is worth everyone’s attention. How can I find out more?

  14. I all the time used to read paragraph in news papers but now
    as I am a user of internet therefore from now I am using net for content, thanks to web.

  15. I’ve been surfing on-line greater than 3 hours lately, but
    I by no means found any interesting article like yours. It is lovely price
    sufficient for me. In my opinion, if all webmasters and
    bloggers made just right content as you did, the web will be a lot more helpful
    than ever before.

  16. Greate pieces. Keep posting such kind of info on your site.
    Im really impressed by it.
    Hi there, You have performed an excellent job. I will definitely digg it and for my part recommend to my friends.
    I’m sure they will be benefited from this website.

  17. That is really interesting, You are an excessively professional
    blogger. I’ve joined your feed and sit up for searching for extra of your wonderful post.
    Also, I have shared your website in my social networks

  18. quest bars says:

    Great post however , I was wanting to know if you could write
    a litte more on this topic? I’d be very thankful if you could elaborate a little bit further.
    Bless you!

  19. Thanks for the marvelous posting! I genuinely enjoyed reading it, you are a great author.I will remember to bookmark your blog
    and definitely will come back at some point. I want to encourage you
    continue your great work, have a nice holiday weekend!

  20. I just want to tell you that I am just new to blogs and honestly liked you’re website. Very likely I’m going to bookmark your website . You definitely have perfect posts. Regards for sharing your blog.

  21. Yay google is my world beater helped me to find this great web site…

  22. Hey! I could have sworn I’ve been to this website before but after browsing through some of the post I realized it’s new to me.

  23. Thank you for every other great post. The place else may just anyone get that type of info in such a perfect way of writing? I have a presentation next week, and I am at the look for such info.

  24. Pretty nice post. I just stumbled upon your weblog and wished to say that I have really enjoyed surfing around your blog posts. After all I’ll be subscribing to your rss feed and I hope you write again soon!

Leave a Reply

Your email address will not be published.


4 + 15 =

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

iTownz | Your Internet Destination – National Free Directory and Local Resource Guide
Back to Main Page